#7J303-57810FR Kubota Standard L & MX Series Brush Guard Insert

(55 minutes)
Reposition the front end loader and raise the hood to improve drill angles.

4/27/2024
ROUND ROCK, TX
Jon

(20 minutes)
Unlike others, found the drill bit worked great and no need to use a drill punch, just use the existing holes on the grate, also drill a hole in the catch release on the OEM grill and a hole on the left side of it and strung a coated wire through both the make releasing the grill easier.

4/18/2024
LINDEN, TX
Joseph

Unrated (30 minutes)
just plane easy,nice steel on my bull bar, thanks for the drill bit inclued ,nice touch

4/13/2024
Pittsford, NY
Werner

The drill bit that came with it was great very sharp went right thru the metal. Brush Screen Kit was the right choice for my L4701 kobota.

10/24/2023
MT HOLLY, NC
Richard

Unrated (1 hour)
Have a strong drill motor.

10/23/2023
VALLEY VIEW, TX
Andy

(30 minutes)
Take an extra drill bit.

10/5/2023
SANDERSVILLE, GA
Thomas

After securing lower mounts with factory hardware. Use two clamps to hold upper guard securely in place while spotting holes to drill in factory brush guard. This allows both hands free for center punching the metal before starting to drill and hands-free operation to drill holes and allows proper alignment prior to drilling as you can step back and make sure its correctly aligned. Great addition to my L4701. Takes away the worry I had about pressing a limb or branch through plastic grille while using grapple or forks.

9/29/2023
COLUMBIA, MS
Tommy

(30 minutes)
1 1/16” wrench + Cresent wrench. 7/16 wrench for the top nut. Center punch + 1/8” starter drill bit. If I had to do it again it would take 1/2 the time. Great fit!

9/10/2023
SAVANNAH, GA
WILLIAM

Unrated (30 minutes)
Worked slick. However make sure to have extra drill bit the one provided broke right off the bat. Other than that no problem. PS. I used clamps on the top side before drilling .

8/19/2023
JASPER, GA
Mark

Unrated (45 minutes)
I didn’t remove front end loader. Just rested it on the ground. Plenty of room to work between loader and tractor.

7/29/2023
Kinder, LA
John

(30 minutes)
Very straightforward install. Appreciate the drill bit and Allen wrench for ease of install.

7/27/2023
GULF BREEZE, FL
Jeff

(1 hour)
I used a clamp to stabilize the guard when drilling small hole. Be careful not to stress the guard because this might misalign the holes when you go to put the bolt in.

7/21/2023
WAUSAUKEE, WI
Richard

Unrated (20 minutes)
One drill bit was sent which was nice to have the right size without having to run to the hardware store but you will need 2 for the job most likely.

7/6/2023
MILLERS CREEK, NC
Evergreen

(30 minutes)
After marking your holes use a punch to keep the drill from walking. I used a smaller bit than the one provided to drill a starter hole then switched to the provided bit. Set your drill on slow speed and use some oil.

7/3/2023
FLORA, MS
Calvin

Unrated (20 minutes)
Clamp helps with drilling the 2 holes.

6/1/2023
Madisonville, KY
Roger

(30 minutes)
Mount the bottom first then get a center punch to mark the upper holes. Drill a pilot hole then drill the final hole size. Easy install.

5/10/2023
ELWOOD, IN
Bradley

Unrated (1 hour)
Nuts require a 27mm wrench. 1-1/16" is pretty much exactly the same size.

5/10/2023
OGDENSBURG, NY
mike

Unrated (30 minutes)
Use of a punch to start the drill and motor/cutting oil helps. Well built. Shipping was very speedy. Highly recommend.

5/9/2023
Orange, CT
Joseph

(30 minutes)
watched video on installation was helpful

4/24/2023
STEELEVILLE, IL
jeff

Unrated (30 minutes)
I installed it without removing the loader and it was no problem.

4/24/2023
SAINT ALBANS, VT
Darren

(2 hours)
Use 2 large c-clamps

4/21/2023
LA MARQUE, TX
Mike

(20 minutes)
cake walk

4/15/2023
HILTON, NY
Muir