#RACKS360 RACKS360 - Roll Bar Tool Carrying System
$139.99
11 In Stock
Weight: 6.30 lbs
- The RACKS360 mounting system rotates 360 degrees to allow tools of many shapes and sizes to be attached securely no matter your rollbar's angle or configuration.
- This allows you to keep your tools with you wherever you go so you can multi-task efficiently.
- FITS: Round, Square and Rectangular roll bars
- Hardware and basic installation tools included
- Maximum Weight Limits:
- Top Racks weight limit = 20lbs
- Bottom Racks weight limit = 20lbs
- Fits the following Rollbar sizes:
- 2” round & up to 2 1/2" round
- 2” square
- 1.5 x 3 (Mounts on 3” side of roll bar)
- 2" x 3 (Mounts on 3” side of roll bar)
- Install Instructions
element not set
This part fits your tractor
This part fits 0 models
Installation Tips
(15 minutes)
Had to get longer bolts the two bolts that come with it don't fit with larger spacer supplied
Had to get longer bolts the two bolts that come with it don't fit with larger spacer supplied
7/8/2025
FOREST LAKE, MN
Michael
FOREST LAKE, MN
Michael
(2 hours)
The only problem was supplied bolts were too short and I had to go to 2 local stores for the right size. Quality product once installed.
The only problem was supplied bolts were too short and I had to go to 2 local stores for the right size. Quality product once installed.
5/23/2025
WEEDSPORT, NY
Granito
WEEDSPORT, NY
Granito
(8 minutes)
No tips or tricks required. The build quality is amazing. I bought one for my zero turn and loved it so much I bought one for my Kubota compact tractor.
No tips or tricks required. The build quality is amazing. I bought one for my zero turn and loved it so much I bought one for my Kubota compact tractor.
5/22/2025
SEATTLE, WA
Jeff
SEATTLE, WA
Jeff
Unrated
Couldn’t have been any easier to install on my 2017 Kubota 2601.
Couldn’t have been any easier to install on my 2017 Kubota 2601.
12/12/2023
FLANDERS, NJ
James
FLANDERS, NJ
James
Unrated
(5 minutes)
I needed to use longer bolts because my rops was wider but no big deal works fine looks good also
I needed to use longer bolts because my rops was wider but no big deal works fine looks good also
7/14/2022
Dundalk, MD
Joseph
Dundalk, MD
Joseph
(10 minutes)
No spacers were required for my Kubota B3200. The only suggestion I have is that I put a 3/8" external toothed star washer between each knob and the flat washers, just because there's a lot of vibration on tractors and it seemed like a good idea to prevent things from vibrating loose. Other than that, it was very straight-forward.
No spacers were required for my Kubota B3200. The only suggestion I have is that I put a 3/8" external toothed star washer between each knob and the flat washers, just because there's a lot of vibration on tractors and it seemed like a good idea to prevent things from vibrating loose. Other than that, it was very straight-forward.
6/10/2022
LOUISA, VA
BILL
LOUISA, VA
BILL
Unrated
Would have been 15 minutes except I didn't know that you had to seat the nuts inside the unit by screwing in the bolts prior to assembling the unit. That wasn't in the direction. Had to call for technical support. They need to add that step to the instructions.
Would have been 15 minutes except I didn't know that you had to seat the nuts inside the unit by screwing in the bolts prior to assembling the unit. That wasn't in the direction. Had to call for technical support. They need to add that step to the instructions.
4/15/2022
VILLA GROVE, IL
Thomas
VILLA GROVE, IL
Thomas
Unrated
(25 minutes)
Had to route the wires running to my lights
Had to route the wires running to my lights
12/8/2021
Show all 9
If your ROPS is 2 inch or wider, order the longer bolts from Messick's or you will have to buy 2 5/16 -18 x 2 3/4" Allen head bolts to make this work. Also helps to have second pair of hands so front and back can be held in place while attempting to tighten bolts. I used a slide clamp to hold it together.
Pinckney, MI
Donald